ProSoft Technology ProTalk PTQ-104C Manual de usuario Pagina 3
- Pagina / 181
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Electrical Ratings
Backplane Current Load: 800 mA @ 5 V DC; 3mA @ 24V DC
Operating Temperature: 0 to 60°C (32 to 140°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Shock: 30g Operational; 50g non-operational; Vibration: 5 g from 10 to 150 Hz
Relative Humidity 5% to 95% (non-condensing)
All phase conductor sizes must be at least 1.3 mm(squared) and all earth ground conductors must be at least
4mm(squared).
Markings:
ANSI / ISA ISA 12.12.01 Class I Division 2, GPs A, B, C, D
CSA/cUL C22.2 No. 213-1987
CSA CB Certified IEC61010
ATEX EN60079-0 Category 3, Zone 2
EN60079-15
243333
Important Notice:
CAUTION: THE CELL USED IN THIS DEVICE MAY PRESENT A FIRE
OR CHEMICAL BURN HAZARD IF MISTREATED. DO NOT
DISASSEMBLE, HEAT ABOVE 100°C (212°F) OR INCINERATE.
Maximum battery load = 200 μA.
Maximum battery charge voltage = 3.4 VDC.
Maximum battery charge current = 500 μA.
Maximum battery discharge current = 30 μA.
Your Feedback Please
We always want you to feel that you made the right decision to use our products. If you have suggestions, comments,
compliments or complaints about the product, documentation, or support, please write or call us.
ProSoft Technology
5201 Truxtun Ave., 3rd Floor
Bakersfield, CA 93309
+1 (661) 716-5100
+1 (661) 716-5101 (Fax)
www.prosoft-technology.com
support@prosoft-technology.com
Copyright © ProSoft Technology, Inc. 2009. All Rights Reserved.
PTQ-104S User Manual
October 05, 2009
ProSoft Technology
®
, ProLinx
®
, inRAx
®
, ProTalk
®
, and RadioLinx
®
are Registered Trademarks of ProSoft
Technology, Inc. All other brand or product names are or may be trademarks of, and are used to identify products
and services of, their respective owners.
- PTQ-104S 1
- Information for ProTalk 2
- Product Users 2
- Warnings 2
- Important Notice: 3
- Your Feedback Please 3
- ProSoft Technology 4
- Product Documentation 4
- Contents 5
- 1 Start Here 9
- 1.1.3 PC and PC Software 10
- In This Chapter 13
- TART / PROGRAMS / CONCEPT 14
- MODCONNECT TOOL 14
- FILES directory on the 14
- 2.2 Create a New Project 16
- PLC CONFIGURATION 18
- CONFIGURATION dialog box 19
- MODULE SELECTION dialog 20
- PECIALS 22
- PECIALS dialog box 22
- AVE PROJECT AS dialog box 24
- SERIES as QUANTUM): 32
- 4.1 Create a New Project 35
- ROJECT BROWSER, expand 36
- EW DEVICE 36
- to continue 37
- 4.3 Build the Project 39
- ROGRESS dialog 40
- IAGNOSTICS 48
- IAGNOSTICS dialog box 48
- to open the Main Menu 48
- ATABASE VIEW MENU 49
- 6 Module Configuration 51
- 6.1.1 Set Up the Project 52
- 6.1.2 Set Module Parameters 54
- 6.2.1 Module Name 55
- 6.2.2 Failure Flag Count 55
- 6.2.3 Error Offset 56
- 6.2.4 Initialize Output Data 56
- 6.3 Backplane Data Exchange 56
- 6.3.1 Data Transfer 57
- Example: 40000 + 1 = 40001 58
- 6.4.4 Read Status (9250) 69
- 6.4.5 Event Messages (9958) 71
- 6.5 [SNTP CLIENT] 75
- 6.6 [IEC-870-5-104] 76
- 6.6.1 Use IP List 76
- 6.6.2 Override StartDT 76
- 6.6.9 Time DB Offset 78
- 6.6.10 Error Offset 78
- 6.6.11 Command Delay Timer 78
- 6.6.18 Interval for Freeze 80
- 6.6.19 Set Priority Queues 80
- 6.6.20 Cyclic Set IV Time 81
- 6.6.21 IV Check Delay Time 81
- 6.6.22 IV Fail Count 81
- 6.6.23 Event Scan Delay 81
- 6.6.24 Scan Events 81
- 6.6.25 Time Type 82
- 6.8 [IEC-870-5-104 Database] 82
- 6.8.1 Short Pulse Time 82
- 6.8.2 Long Pulse Time 83
- 6.8.3 Point Count 83
- 6.8.4 Sequence Flag 84
- 6.8.5 Parameter Offset 85
- 6.9 [M_SP_NA_1 104] 86
- 6.10 [M_DP_NA_1 104] 86
- 6.11 [M_ST_NA_1 104] 86
- 6.12 [M_ME_NA_1 104] 87
- 6.13 [M_ME_NB_1 104] 87
- 6.14 [M_ME_NC_1 104] 87
- 6.15 [M_IT_NA_1 104] 88
- 6.16 [C_SC_NA_1 104] 88
- 6.17 [C_DC_NA_1 104] 89
- 6.18 [C_RC_NA_1 104] 89
- 6.19 [C_SE_NA_1 104] 89
- 6.20 [C_SE_NB_1 104] 90
- 6.21 Ethernet Configuration 90
- OWNLOAD button 92
- OWNLOAD dialog 92
- 7.1 Required Hardware 95
- 7.2.2 Navigation 98
- 7.2.3 Keystrokes 98
- 7.2.4 Main Menu 99
- 7.2.5 Database View Menu 102
- to open the IEC-870-5-104 104
- 7.2.7 Network Menu 106
- 7.3 LED Status Indicators 107
- 7.3.2 Error Status Table 108
- 8 Reference 109
- 8.1.2 General Specifications 110
- 8.2.1 Module Address 112
- 8.2.3 Using Monitor Points 117
- D 03/26/2004 00:00:00 125
- H 03/25/2004 19:00:00 125
- M 03/25/2004 18:08:00 125
- 300 Low Byte of word 20 128
- 301 Low Byte of word 30 128
- 302 High Byte of word 40 128
- 100 Bit 0 of word 100 132
- 101 Bit 1 of word 100 132
- 102 Bit 2 of word 100 132
- 8.2.5 Data Communication 135
- 8.2.6 Events 141
- Type Command 142
- 8.3 Cable Connections 151
- 8.3.1 Ethernet Connection 151
- 8.4 Error Status Table 153
- Data Field(s) Description 154
- 8.5 Group Codes 156
- Monitor Database 159
- Address 159
- Require Select 159
- 8.7.1 System or device 161
- 8.7.2 Application Layer 161
- Parameter Value Remarks 170
- 9.2.1 All Product Returns: 174
- 9.3 LIMITED WARRANTY 175
- 9.3.8 No Other Warranties 178
- 9.3.9 Allocation of Risks 178
- PC and PC Software • 10 180
- Time Information • 148 181
© 2020, manymanuals.es. Todos los derechos reservados | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales