Prosoft-technology 5201-DFNT-104S Manual de usuario Pagina 36
- Pagina / 157
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
104S v2 ♦ ProLinx Gateway Configure the Gateway
(Firmware v2.xx) Protocol Manual
Page 36 of 157 ProSoft Technology, Inc.
March 19, 2010
2.1.18 Group Codes
One aspect of the point configuration database that leads to confusion is the
group definition field. This assignment for each point assigns a point to one or
more interrogation groups. Use of interrogation groups permits the controlling
unit to interface with a specific set of data. Refer to the IEC 60870-5-104
standard for a full discussion of interrogation groups. A specific group, Periodic
data group, reports data points on a set frequency. The frequency is set in the
Cyclic Data Transmission parameter in the configuration file. Remember that a
point can be assigned to more than one group.
Group Code Description
0x00000001 Interrogated by general interrogation (station or global)
0x00000002 Interrogated by group 1 interrogation
0x00000004 Interrogated by group 2 interrogation
0x00000008
Interrogated by group 3 interrogation (See Note 1, below)
0x00000010 Interrogated by group 4 interrogation
0x00000020 Interrogated by group 5 interrogation
0x00000040 Interrogated by group 6 interrogation
0x00000080 Interrogated by group 7 interrogation
0x00000100 Interrogated by group 8 interrogation
0x00000200 Interrogated by group 9 interrogation
0x00000400 Interrogated by group 10 interrogation
0x00000800 Interrogated by group 11 interrogation
0x00001000 Interrogated by group 12 interrogation
0x00002000 Interrogated by group 13 interrogation
0x00004000 Interrogated by group 14 interrogation
0x00008000 Interrogated by group 15 interrogation
0x00010000 Interrogated by group 16 interrogation
0x00020000 Interrogated by general counter request
0x00040000 Interrogated by group 1 counter request
0x00080000 Interrogated by group 2 counter request
0x00100000 Interrogated by group 3 counter request
0x00200000 Interrogated by group 4 counter request
0x40000000 Disable event scanning of this point
0x80000000 Periodic/cyclic data returned from unit
Note 1: Group 3 interrogation also returns the parameter data (ASDU 110 – threshold, low limit
and high limit) for all monitored measured points.
- 104S v2 1
- All ProLinx 2
- Products 2
- Your Feedback Please 3
- ProSoft Technology 3
- Product Documentation 3
- Contents 5
- 1 Start Here 9
- 1.2.1 Using the Online Help 10
- 2 Configure the Gateway 13
- 2.1.1 [SNTP CLIENT] 14
- 2.1.2 [IEC-870-5-104] 16
- O (0) or YES (1) 17
- ES or NO 20
- or more 21
- ONE, 1 = CP24, or 2 = CP56 23
- ES or NO 27
- 2.1.5 [M_SP_NA_1 104] 29
- 2.1.6 [M_DP_NA_1 104] 30
- 2.1.7 [M_ST_NA_1 104] 30
- 2.1.8 [M_ME_NA_1 104] 30
- 2.1.9 [M_ME_NB_1 104] 31
- 2.1.10 [M_ME_NC_1 104] 31
- 2.1.11 [M_IT_NA_1 104] 32
- 2.1.12 [C_SC_NA_1 104] 32
- 2.1.13 [C_DC_NA_1 104] 33
- 2.1.14 [C_RC_NA_1 104] 33
- 2.1.15 [C_SE_NA_1 104] 34
- 2.1.16 [C_SE_NB_1 104] 34
- 2.1.17 [C_SE_NC_1 104] 35
- 2.1.18 Group Codes 36
- 2.2 CommonNet Data Map 38
- 2.2.1 From Address 39
- 2.2.2 To Address 39
- 2.2.3 Register Count 39
- 2.2.4 Swap Code 39
- 2.2.5 Delay Preset 40
- OWNLOAD dialog box opens 41
- OWNLOAD button 41
- Implementation 43
- 3.1 Module Address 44
- 3.1.1 IP Address 44
- 3.1.2 Common ASDU Address 46
- 3.3 Using Monitor Points 49
- 3.3.1 Monitor Data Transfer 50
- Example - Mode A 54
- D 03/26/2004 00:00:00 55
- H 03/25/2004 19:00:00 55
- M 03/25/2004 18:08:00 55
- Example (C_SC_NA) 63
- 3.4.1 Control Data Transfer 64
- 3.5 Data Communication 70
- 3.5.1 Group Communication 70
- 3.5.2 STARTDT & STOPDT 72
- 3.5.3 TESTFR Requests 73
- 3.6 Events 75
- 3.6.1 Deadbands 76
- Example: 78
- 3.6.3 Time Information 83
- CHECK DELAY TIME 84
- 3.6.5 Event Priority 87
- 3.6.6 SNTP Support 88
- 3.7 Sequence Flag 89
- 4.1.1 Required Hardware 91
- IAGNOSTICS 92
- IAGNOSTICS dialog box 92
- to open the Main Menu 93
- 4.1.3 Navigation 94
- 4.1.4 Database View Menu 97
- to open the IEC-870-5-104 100
- 4.1.6 Network Menu 102
- to return to the Main Menu 103
- 4.2 LED Indicators 104
- 5 Reference 105
- 5.2.1 Introduction 109
- 5.2.2 Configuration 109
- Word Offset Description 110
- 5.2.3 Command Block List 111
- 5.3 SNTP Support 123
- 5.3.1 SNTP Status Data 123
- 5.5 Command Qualifiers 126
- 5.6 Parameter Qualifiers 127
- 5.7.1 System or device 128
- 5.7.2 Application Layer 128
- In This Chapter 138
- Monitor Database 143
- Address 143
- Require Select 143
- 5.8.4 C_RC_NA_1 Form 145
- 6.2.1 All Product Returns: 148
- 6.3 LIMITED WARRANTY 150
- 6.3.8 No Other Warranties 153
- 6.3.9 Allocation of Risks 153
Relacionado con productos y manuales para Relé Prosoft-technology 5201-DFNT-104S
Relé Prosoft-technology AN-X-AMX Manual de usuario
(44 paginas)
(44 paginas)
Relé Prosoft-technology AN-X-AMX Manual de usuario
(50 paginas)
(50 paginas)
Relé Prosoft-technology AN-X-AMX Manual de usuario
(55 paginas)
(55 paginas)
Relé Prosoft-technology AN-X-AMX Manual de usuario
(68 paginas)
(68 paginas)
Relé Prosoft-technology AN-X2-SQD Manual de usuario
(51 paginas)
(51 paginas)
Relé Prosoft-technology AN-X2-GENI Manual de usuario
(64 paginas)
(64 paginas)
Relé Prosoft-technology 5201-MNET-101S Manual de usuario
(159 paginas)
(159 paginas)
Relé Prosoft-technology 5205-104S-PDPS Manual de usuario
(128 paginas)
(128 paginas)
Relé Prosoft-technology AN-X-PB Manual de usuario
(61 paginas)
(61 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.029 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales