ProSoft Technology inRA-x ILX34-AENWG Guia de preparacion descargar pdf (Pagina 4)

European Hazardous Location Approval

European Zone 2 Certification (The following applies when the product bears the EEx Marking)

This equipment is intended for use in potentially explosive atmospheres as defined by European Union Directive

94/9/EC.

The ATEX test report certifies that this equipment has been found to comply with the Essential Health and Safety

Requirements relating to the design and construction of Category 3 equipment intended for use in potentially

explosive atmospheres, given in Annex II to this Directive. The examination and test results are recorded in a

confidential report.

Compliance with the Essential Health and Safety Requirements has been assured by compliance with EN 60079-0

and EN60079-15.

Important: Observe the following additional Div 2 certification requirements.

 This equipment is not resistant to sunlight or other sources of UV radiation.

 The secondary of a current transformer shall not be open-circuited when applied in Class I, Div 2 environments.

 Equipment of lesser Enclosure Type Rating must be installed in an enclosure providing at least IP54 protection

when applied in Class I, Div 2 environments.

 This equipment shall be used within its specified ratings defined by Allen-Bradley.

 Provision shall be made to prevent the rated voltage from being exceeded by transient disturbances of more than

40% when applied in Class I, Div 2 environments.

North American Hazardous Location Approval

The following information applies when operating this equipment in hazardous locations:

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate

indicating the hazardous location temperature code. When combining products within a system, the most adverse

temperature code (lowest "T" number) may be used to help determine the overall temperature code of the system.

Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at

the time of installation.

Warning: EXPLOSION HAZARD -

Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous.

Do not disconnect connections to this equipment unless power has been removed or the area is known to be

nonhazardous. Secure any external connections that mate to this equipment by using screws, sliding latches,

threaded connectors, or other means provided with this product.

Substitution of components may impair suitability for Class I, Division 2.

If this product contains batteries, they must only be changed in an area known to be nonhazardous.

Informations sur l'utilisation de cet équipement en environnements dangereux:

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne conviennent qu'à une utilisation en environnements de Classe I

Division 2 Groupes A, B, C, D dangereux et non dangereux. Chaque produit est livré avec des marquages sur sa

plaque d'identification qui indiquent le code de température pour les environnements dangereux. Lorsque plusieurs

produits sont combinés dans un système, le code de température le plus défavorable (code de température le plus

faible) peut être utilisé pour déterminer le code de température global du système. Les combinaisons d'équipements

dans le système sont sujettes à inspection par les autorités locales qualifiées au moment de l'installation.

Avertissement: RISQUE D'EXPLOSION –

Couper le courant ou s'assurer que l'environnement est classé non dangereux avant de débrancher l'équipement.

Couper le courant ou s'assurer que l'environnement est classé non dangereux avant de débrancher les connecteurs.

Fixer tous les connecteurs externes reliés à cet équipement à l'aide de vis, loquets coulissants, connecteurs filetés ou

autres moyens fournis avec ce produit.

1 2 3 4 5 6 7 8 9 ... 78 79

Comentarios a estos manuales

Sin comentarios

ProSoft Technology inRA-x ILX34-AENWG Guia de preparacion Pagina 4

Comentarios a estos manuales